STOVE / RANGE FAULT CODES
|
This is a general guide to stove / range fault code. This guide may be incomplete as manufactures use different parts on different models. We assume no responsibility for any action taken on your part as a result of using this guide. Consult your owners manual, as it may give the fault codes for your particular model.
GENERAL ELECTRIC HOTPOINT RCA
|
Display
|
Condition
|
Repair
|
F0 and F1
|
Failed Thermistor Control
|
Replace ERC
|
F2
|
Oven Temp Exceeds 590 w/unlocked door
|
High resistance or interference in sensor Likely a bad sensor
|
F3
|
Open sensor circuit
|
Bad sensor or open sensor fuse
|
F8
|
Component failure
|
Replace ERC
|
F9
|
Program w/door circuit
|
Check Wiring
|
FRIGIDAIRE TAPPAN GIBSON WESTINGHOUSE
|
Display
|
Condition
|
Repair
|
F0 & F1
|
EOC failure
|
Replace EOC
|
F2
|
Oven too hot
|
Likely a bad sensor (should read 1100 ohms) Possible bad EOC
|
F3
|
Oven Sensor Open
|
Replace sensor
|
F4
|
Oven Sensor Shorted
|
Replace sensor
|
F5 or F6 or F7
|
EOC failure
|
Replace EOC
|
F8
|
Lock switches
|
Check operation of lock switch(s)
|
WHIRLPOOL ROPER KITCHENAID
|
NOTE: Not valid for Y line. If there is a Y near the end of your model number, do not use this chart.
|
Display
|
Condition
|
Repair
|
4 Digit Display
|
FO - E0
|
Analog to Digital Failure
|
Disconnect for 30 seconds- if display re-appears- replace control
|
F1 - E1
|
Safety flip flop
|
replace
|
F2 - E0
|
shorted keypad
|
replace
|
F3 - E0
|
sensor or sensor fuse opened
|
replace sensor or fuse
|
F3 - E1
|
sensor shorted
|
replace sensor
|
F3 - E2
|
oven too hot
|
replace sensor
|
F3 - E3
|
clean temp. too hot
|
replace sensor
|
F5 - E0 F5 - E1 and E2
|
check door/latch switch
|
replace
|
2 Digit Display
|
F0 or F1 or F5
|
Failed transistor
|
Replace ERC
|
F2
|
Oven temp too high
|
1. Test operation of door lock on self-clean models.
2. Test relay contact operation
3. High resistance in sensor (should be apx. 1100 ohms)
|
F3
|
Open sensor or thermal fuse
|
Replace sensor or thermal fuse
|
F4
|
Shorted sensor
|
Replace sensor
|
F6
|
Problem in time keeping circuit
|
1. Reset time and/or cooking operation
2. Check for proper ground
|
F7
|
Stuck function switch or button on ERC
|
Replace ERC
|
F8
|
Failure of ERC
|
Replace ERC
|
F9
|
Door lock circuit
|
Check wiring and test operation of door lock switch
|
MAYTAG MAGIC CHEF JENNAIR ADMIRAL
|
Display
|
Condition
|
Repair
|
F1
|
watch dog on board
|
bad touchpad or clock
see FAQ for procedure
|
F2
|
oven too hot
|
bad relay board (if present) or bad sensor
|
F3 or F4
|
open or shorted sensor
|
replace sensor
|
F5
|
hardware and watchdog circuits disagree
|
replace clock
|
F6
|
missing AC signal
|
Check for proper voltage
|
F7
|
function key shorted
|
replace touch pad or clock
|
F8
|
A/D supervisory
|
replace clock
|
F9
|
door latch supervisory
|
check door lock circuit or replace clock
|
F0
|
function key stuck
|
replace touch pad or clock
|
Display -glass link ERC
|
Condition
|
Repair
|
door flashing #0,1,2,3
|
latch switch broken
|
replace
|
lock flashing
|
latch switch broken
|
replace
|
F 0
|
loss of safety signal
|
replace adapter board
|
F 1
|
watchdog circuit
|
replace ERC
|
F 2
|
oven too hot
|
check sensor-1100 ohms
|
F3 F4
|
open or shorted sensor
|
replace sensor
|
F7
|
shorted touch panel
|
replace glass panel
|
F9
|
motorized door
|
check latch
|
FF
|
lock error
|
check switch and motor
|
ERC III / Relay board with separate board / push buttons
|
F0
|
shorted push pad
|
replace
|
F1
|
failed ERC
|
replace
|
F2
|
oven too hot
|
check sensor 1100 ohms
|
F3 F4
|
shorted or open sensor
|
replace
|
F5,F6,F8
|
failed ERC
|
replace
|
F7
|
shorted or sticking button
|
check glass alignment
|
F9
|
door latch failure
|
replace
|
SOURCE:
AHASC Of New Jersey with revisions by Mike Garrell.
|